Trouble with a Adaptec 2010S RAID PCI adapter

Hi list, I'm in trouble trying to use a Adaptec 2010S RAID PCI adapter
in a i386 linux box running kernel 2.6.6. I've enabled I2O in the kernel
and support for my SCSI adapter, that in fact works fine.

CONFIG_I2O=y
CONFIG_I2O_CONFIG=y
CONFIG_I2O_BLOCK=y
CONFIG_I2O_SCSI=y
CONFIG_I2O_PROC=y

My dmesg shows something like this:

.......
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36

aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
.......
Red Hat/Adaptec aacraid driver (1.1.2-lk1 Jun 4 2004)
.......
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 20
i2o: Checking for PCI I2O controllers...
i2o: I2O controller on bus 4 at 16.
i2o: PCI I2O controller at FEBFC000 size=16384
i2o/iop0: Installed at IRQ0
i2o: 1 I2O controller found and installed.
Activating I2O controllers...
This may take a few minutes if there are many devices
Unable to obtain status of i2o/iop0, attempting a reset.
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2o_scsi.c: Version 0.1.2
chain_pool: 0 bytes @ f7d11f9c
(512 byte buffers X 4 can_queue X 0 i2o controllers)


It seens that the kernel has found the controoler. Then I headed to
http://i2o.shadowconnect.com/ - I2O on Linux Home and got their
raidutil package. But here starts the problem, even simple commands like

raidutil -L controller

gives me the error:

Engine connect failed: COMPATIBILITY number
osdIOrequest : File /dev/dpti17 Could Not Be Opened


Following the site info I have applied the following patchs to my kernel:

i2o-64-bit-fix.patch
i2o-adaptec-zerochannel-support.patch
i2o-config-clean.patch
i2o-makefile-cleanup.patch
i2o-pae-support.patch
i2o-passthru.patch
i2o_block-cleanup.patch
i2o_cmd_passthru-reorder.patch
i2o_config-checking-bugfix.patch
i2o_proc-full-seq_file.patch
i2o_proc-lct-access-bugfix.patch

with no luck. I've tried Adaptec's asmbe_linux_v1.23.006.tgz tools, but
aaccli cannot find the controller as well.

Does anybody experienced a problem like this before? I've found some
messages on mailling lists with the same error message, but no
solutions. I'm new to I2O. Am I missing something?

tks in advance for any help.

Andre



-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

RE: Trouble with a Adaptec 2010S RAID PCI adapter

The 2010 Adapter is a Zero Channel RAID card that does *not* purely
follow the I2O standard. It separates out the message unit from the
message pool, each having its own Base Address register (BAR) rather
than a single unifying BAR.

There were recent patches to the I2O layer to support this adapter
posted to the linux-scsi list. Pick them up and check them out. I
believe that there are still problems with that code.

The dpt_i2o driver, which supports 64 bit operation, continues to
properly support this adapter in the 2.6 tree, and updates to this
driver were also posted to the linux-scsi list w/o feedback (so in, not
in, don't know).

Sincerely -- Mark Salyzyn

-----Original Message-----
From: linux-raid-owner@vger.kernel.org
[mailto:linux-raid-owner@vger.kernel.org] On Behalf Of Andre Correa
Sent: Tuesday, June 15, 2004 1:01 PM
To: linux-raid@vger.kernel.org
Subject: Trouble with a Adaptec 2010S RAID PCI adapter


Hi list, I'm in trouble trying to use a Adaptec 2010S RAID PCI adapter
in a i386 linux box running kernel 2.6.6. I've enabled I2O in the kernel

and support for my SCSI adapter, that in fact works fine.

CONFIG_I2O=y
CONFIG_I2O_CONFIG=y
CONFIG_I2O_BLOCK=y
CONFIG_I2O_SCSI=y
CONFIG_I2O_PROC=y

My dmesg shows something like this:

.......
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36

aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
.......
Red Hat/Adaptec aacraid driver (1.1.2-lk1 Jun 4 2004)
.......
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 20
i2o: Checking for PCI I2O controllers...
i2o: I2O controller on bus 4 at 16.
i2o: PCI I2O controller at FEBFC000 size=16384
i2o/iop0: Installed at IRQ0
i2o: 1 I2O controller found and installed.
Activating I2O controllers...
This may take a few minutes if there are many devices
Unable to obtain status of i2o/iop0, attempting a reset.
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2o_scsi.c: Version 0.1.2
chain_pool: 0 bytes @ f7d11f9c
(512 byte buffers X 4 can_queue X 0 i2o controllers)


It seens that the kernel has found the controoler. Then I headed to
http://i2o.shadowconnect.com/ - I2O on Linux Home and got their
raidutil package. But here starts the problem, even simple commands like

raidutil -L controller

gives me the error:

Engine connect failed: COMPATIBILITY number
osdIOrequest : File /dev/dpti17 Could Not Be Opened


Following the site info I have applied the following patchs to my
kernel:

i2o-64-bit-fix.patch
i2o-adaptec-zerochannel-support.patch
i2o-config-clean.patch
i2o-makefile-cleanup.patch
i2o-pae-support.patch
i2o-passthru.patch
i2o_block-cleanup.patch
i2o_cmd_passthru-reorder.patch
i2o_config-checking-bugfix.patch
i2o_proc-full-seq_file.patch
i2o_proc-lct-access-bugfix.patch

with no luck. I've tried Adaptec's asmbe_linux_v1.23.006.tgz tools, but
aaccli cannot find the controller as well.

Does anybody experienced a problem like this before? I've found some
messages on mailling lists with the same error message, but no
solutions. I'm new to I2O. Am I missing something?

tks in advance for any help.

Andre



-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

Re: Trouble with a Adaptec 2010S RAID PCI adapter

Salyzn tks for the info. Following it I found the thread: [patch 1/1]
Get I2O working with Adaptec's zero channel controllers,
(http://groups.google.com/groups?q=2010s+group:mlist.linux.s csi&hl=en&lr=&ie=UTF-8&group=mlist.linux.scsi&selm=linux.scs i.200405290713.i4T7Dxr25622%40mail.osdl.org&rnum=1)
where the patch is posted. The thread is really unanswered and the
patch is the same from http://i2o.shadowconnect.com where it is called
i2o-adaptec-zerochannel-support.patch

I already had it applied to my kernel and couldn't make the adapter work.

I'll have a look on dpt_i2o...

Anyway, my results are that this patch is not working for a Adaptec
2010S card. I'm copying Mr Andrew Morton who first posted the patch so
he gets aware of it. (sorry if you get it doubled, I don't know if you
are at linux-raid).

tks for your attention...

Andre



Salyzyn, Mark wrote:
> The 2010 Adapter is a Zero Channel RAID card that does *not* purely
> follow the I2O standard. It separates out the message unit from the
> message pool, each having its own Base Address register (BAR) rather
> than a single unifying BAR.
>
> There were recent patches to the I2O layer to support this adapter
> posted to the linux-scsi list. Pick them up and check them out. I
> believe that there are still problems with that code.
>
> The dpt_i2o driver, which supports 64 bit operation, continues to
> properly support this adapter in the 2.6 tree, and updates to this
> driver were also posted to the linux-scsi list w/o feedback (so in, not
> in, don't know).
>
> Sincerely -- Mark Salyzyn
>
> -----Original Message-----
> From: linux-raid-owner@vger.kernel.org
> [mailto:linux-raid-owner@vger.kernel.org] On Behalf Of Andre Correa
> Sent: Tuesday, June 15, 2004 1:01 PM
> To: linux-raid@vger.kernel.org
> Subject: Trouble with a Adaptec 2010S RAID PCI adapter
>
>
> Hi list, I'm in trouble trying to use a Adaptec 2010S RAID PCI adapter
> in a i386 linux box running kernel 2.6.6. I've enabled I2O in the kernel
>
> and support for my SCSI adapter, that in fact works fine.
>
> CONFIG_I2O=y
> CONFIG_I2O_CONFIG=y
> CONFIG_I2O_BLOCK=y
> CONFIG_I2O_SCSI=y
> CONFIG_I2O_PROC=y
>
> My dmesg shows something like this:
>
> ......
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>
> aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
> ......
> Red Hat/Adaptec aacraid driver (1.1.2-lk1 Jun 4 2004)
> ......
> I2O Core - (C) Copyright 1999 Red Hat Software
> I2O: Event thread created as pid 20
> i2o: Checking for PCI I2O controllers...
> i2o: I2O controller on bus 4 at 16.
> i2o: PCI I2O controller at FEBFC000 size=16384
> i2o/iop0: Installed at IRQ0
> i2o: 1 I2O controller found and installed.
> Activating I2O controllers...
> This may take a few minutes if there are many devices
> Unable to obtain status of i2o/iop0, attempting a reset.
> I2O configuration manager v 0.04.
> (C) Copyright 1999 Red Hat Software
> I2O Block Storage OSM v0.9
> (c) Copyright 1999-2001 Red Hat Software.
> i2o_block: Checking for Boot device...
> i2o_block: Checking for I2O Block devices...
> i2o_scsi.c: Version 0.1.2
> chain_pool: 0 bytes @ f7d11f9c
> (512 byte buffers X 4 can_queue X 0 i2o controllers)
>
>
> It seens that the kernel has found the controoler. Then I headed to
> http://i2o.shadowconnect.com/ - I2O on Linux Home and got their
> raidutil package. But here starts the problem, even simple commands like
>
> raidutil -L controller
>
> gives me the error:
>
> Engine connect failed: COMPATIBILITY number
> osdIOrequest : File /dev/dpti17 Could Not Be Opened
>
>
> Following the site info I have applied the following patchs to my
> kernel:
>
> i2o-64-bit-fix.patch
> i2o-adaptec-zerochannel-support.patch
> i2o-config-clean.patch
> i2o-makefile-cleanup.patch
> i2o-pae-support.patch
> i2o-passthru.patch
> i2o_block-cleanup.patch
> i2o_cmd_passthru-reorder.patch
> i2o_config-checking-bugfix.patch
> i2o_proc-full-seq_file.patch
> i2o_proc-lct-access-bugfix.patch
>
> with no luck. I've tried Adaptec's asmbe_linux_v1.23.006.tgz tools, but
> aaccli cannot find the controller as well.
>
> Does anybody experienced a problem like this before? I've found some
> messages on mailling lists with the same error message, but no
> solutions. I'm new to I2O. Am I missing something?
>
> tks in advance for any help.
>
> Andre
>
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> -
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>

-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html